Agents Administration - Tests
 

Default Parameters for RedisClstrStatusTest

For a cluster-enabled Redis instance, this test reports the composition of the cluster in terms of the number of master nodes and hash slots assigned to the cluster. In addition, the test tracks the status of the hash slots, and notifies administrators if any hash slot fails. Moreover, the test also alerts administrators if any node is added or removed from the cluster.

This page depicts the default parameters that need to be configured for the RedisClstrStatusTest.

  • The TEST PERIOD list box helps the user to decide how often this test needs to be executed.

  • USERNAME parameter is applicable only if the target server is Redis v6 or above. The eG agent has to be configured with the credentials of a user who has Read-only privileges on the monitored Redis Cluster Server. To create a user named eguser,run the following command.

    acl setuser <username> on ><passowrd> allcommands allkeys

    For example, to create a eguser with read only privilege run the following command:acl setuser eguser allkeys -@all +client|list +cluster|info +cluster|nodes +config|get +info +memory|usage +ping +scan +slowlog|get +time +ttl +xinfo|groups +xinfo|stream resetchannels on >password

  • For Redis v6 or above, provide the password for the above mentioned user in the Redis Password textbox. Then, confirm the password by retyping it against CONFIRM PASSWORD.Before v6, Redis did not include the notion of users, and the only authentication strategy was a single login password. In some high security environments, a password may have been set for the Redis server, so as to protect it from unauthorized accesses/abuse. If such a password has been set for the monitored Redis server, then specify that password against REDIS PASSWORD. Then, confirm the password by retyping it against CONFIRM PASSWORD.

      If the Redis server is not password protected, then do not disturb the default setting of this parameter.

      To determine whether/not the target Redis server is password-protected, do the following:

    • Login to the system hosting the Redis server.

    • Open the redis.conf file in the <REDIS_INSTALL_DIR>.

    • Look for the requirepass parameter in the file.

    • If this parameter exists, and is not preceded by a # (hash) symbol, it means that password protection is enabled for the Redis server. In this case, the string that follows the requirepass parameter is the password of the Redis server. For instance, say that the requirepass specification reads as follows:

      requirepass red1spr0

      According to this specification, the Redis server is protected using the password red1spr0. In this case therefore, you need to specify red1spr0 against REDIS PASSWORD.

    • On the other hand, if the requirepass parameter is prefixed by the # (hash) symbol as shown below, it means password protection is disabled.

      # requirepass red1spr0

      In this case, leave the REDIS PASSWORD parameter with its default setting.

  • By default, the CLUSTER NODES parameter is set to auto-discover, indicating that, by default, this test will auto-discover the nodes available in the cluster and report metrics for all the discovered nodes. However, in case of node failures the eG agent needs to connect to any of the available nodes and collect metrics. To this effect, provide a comma-seperated list of nodes in this text box. You should specify the nodes in the following format: HOSTNAME1#PORT1,HOSTNAME2#PORT2,... . For example, 172.16.8.81#30071,172.16.8.81#30072,....

  • By default, the SSL flag is set to No, indicating that the target Redis cluster server is not SSL-enabled by default. To enable the test to connect to an SSL-enabled Redis cluster server, set the SSL flag to Yes.

  • DD FREQUENCY refers to the frequency with which detailed diagnosis measures are to be generated for this test. The default is 1:1. This indicates that, by default, detailed measures will be generated every time this test runs, and also every time the test detects a problem. You can modify this frequency, if you so desire. Also, if you intend to disable the detailed diagnosis capability for this test, you can do so by specifying none against DD FREQUENCY.

  • Once the necessary values have been provided, clicking on the UPDATE button will register the changes made.

When changing default configurations of tests, the values with “$” indicate variables that will be replaced by the eG system according to the specific server being managed - for instance, $hostName is the host/nickname of the target host, $port is the port number of the server being monitored. E.g., for a server xyz:80, $hostName will be changed automatically by the eG manager to “xyz*” and $port will be changed to “80” when configuring a test.